As the drive for a long time useless, now put the disc into the Pretty
[Users questions | Browse:29 | Favorites]
Users questions: As the drive for a long time useless, cause now my computer disk drive G is not shown, and after release into the CD-ROM, CD-ROM drive can read the disks to hear the sound, lights flash drive after a few thus there is no movement, and do not know any questions, please ask all who love our friends a favor and drive now can not take how to do? Jisi me! Even a rookie, in accordance with the method you said to check the problem, even some operations will not, dare not even try, and now even a bit registry check, and even pass the information up, would you then help me see, thank you
Experts answer: drive can not find out on my own computer assembly and maintenance process, the CD-ROM drive letter in the loss, I analyzed and summarized some of the causes and laws, written for reference. The loss of most of the time drive our own installed new software or new drivers after, and it may be that we inadvertently changed CMOS settings or CONFIG.SYS configuration There because the machine infected with a virus and so on. Hardware reasons: 1) data lines or data lines connected anti-corruption. Sometimes just a little wrong, but it will circle around a large, indicating that to solve the problem must be cautious, there is keen powers of observation. When the drive is lost, should first check the data line drive It reversed the (red relative), whether there is loose. If there is no problem in determining when other places, and drive the data lines often move, then try a data cable should be replaced. 2), jumper settings and hard disk drive jumpers when there is conflict, and in the same line to connect the hard drive data will be the same Now can not find the drive (probably not hard), then as long as the drive's jumpers and jump into a different hard drive can be. In order to improve data transfer rates, better to separate the two hard drives and CD-ROM IDE interface. 3), power line failure, lack of voltage of +5 V or +5 V supply voltage is not normal that there is not much Appears. As we drive or removable hard disk excessive force to the power of the D-type plug loose or poor working conditions because the computer plug oxidation rust, drive's power supply not normal (if this is hard to read the disk drive voice will be abnormal, and a large number of bad sectors hard disk surface there), CD-ROM We could find. 4), IDE interface, if a sudden damage of the drive is lost, can not use the drive, then we can swap drives and hard disk interface look. If the re-start the drive and found able to find, but can not find the hard disk, indicating that the original drive's IDE interface, then damage A; If the exchange after the computer starts correctly, but still no optical drive, indicating the reasons is the drive itself, causing the drive letter is missing, then only replace the drive. Anyway, a few money drive. If Windows, do not drive, we can also DOS (re-start the power F8 into the back of the head by DOS, under the surface of non-WIN98 DOS) under the universal use of WIN98 to try to load the driver CD-ROM drive, if able to load successfully, that is, the reason the software should be mainly from the software, find out the reasons. Otherwise, the hardware should be considered. Not the old 586 machine How to install the extra IDE drive interfaces: Although the computer has reached Bensi, but many are still playing 586 heat. As a part of the machine 586 is not integrated on the motherboard IDE interface, hard disk and floppy and serial port is a multi-function card provided, and some integrated on the motherboard. In the absence of extra ID E interface, where installation of optical drives, is very laborious. If we add a multi-functional card installed, only floppy drive interface, serial port, parallel port address conflict enough you busy for a while, not to mention multi-function cards generally do not support ATAPI protocol, which means even if you add the two multifunction cards, but also drive Is not installed on. Do not know that you do not remember the old ISA sound card, then take into account the 586 machine factory is no extra IDE interface, easy to mount CD-ROM, CD-ROM interface, the sound card on the left. Then you run errands, to the secondary market to find an old sound card on the line. Process in the sound card driver Sequence in general have the option to set optical drive, according to the prompts to install on the line. Software, because: 1), IDE driver installation error or a conflict with a driver if we did not install WIN98 or 95 IDE driver will be installed correctly, or when you open the device after installation Explorer View "hard disk controller," which found a yellow exclamation mark, the time of the drive may be found. Under normal circumstances, when we enter the safe mode, of the drive is not there. If we want to use the drive in safe mode, we can Autoexec.BA
Experts answer: drive can not find out on my own computer assembly and maintenance process, the CD-ROM drive letter in the loss, I analyzed and summarized some of the causes and laws, written for reference. The loss of most of the time drive our own installed new software or new drivers after, and it may be that we inadvertently changed CMOS settings or CONFIG.SYS configuration There because the machine infected with a virus and so on. Hardware reasons: 1) data lines or data lines connected anti-corruption. Sometimes just a little wrong, but it will circle around a large, indicating that to solve the problem must be cautious, there is keen powers of observation. When the drive is lost, should first check the data line drive It reversed the (red relative), whether there is loose. If there is no problem in determining when other places, and drive the data lines often move, then try a data cable should be replaced. 2), jumper settings and hard disk drive jumpers when there is conflict, and in the same line to connect the hard drive data will be the same Now can not find the drive (probably not hard), then as long as the drive's jumpers and jump into a different hard drive can be. In order to improve data transfer rates, better to separate the two hard drives and CD-ROM IDE interface. 3), power line failure, lack of voltage of +5 V or +5 V supply voltage is not normal that there is not much Appears. As we drive or removable hard disk excessive force to the power of the D-type plug loose or poor working conditions because the computer plug oxidation rust, drive's power supply not normal (if this is hard to read the disk drive voice will be abnormal, and a large number of bad sectors hard disk surface there), CD-ROM We could find. 4), IDE interface, if a sudden damage of the drive is lost, can not use the drive, then we can swap drives and hard disk interface look. If the re-start the drive and found able to find, but can not find the hard disk, indicating that the original drive's IDE interface, then damage A; If the exchange after the computer starts correctly, but still no optical drive, indicating the reasons is the drive itself, causing the drive letter is missing, then only replace the drive. Anyway, a few money drive. If Windows, do not drive, we can also DOS (re-start the power F8 into the back of the head by DOS, under the surface of non-WIN98 DOS) under the universal use of WIN98 to try to load the driver CD-ROM drive, if able to load successfully, that is, the reason the software should be mainly from the software, find out the reasons. Otherwise, the hardware should be considered. Not the old 586 machine How to install the extra IDE drive interfaces: Although the computer has reached Bensi, but many are still playing 586 heat. As a part of the machine 586 is not integrated on the motherboard IDE interface, hard disk and floppy and serial port is a multi-function card provided, and some integrated on the motherboard. In the absence of extra ID E interface, where installation of optical drives, is very laborious. If we add a multi-functional card installed, only floppy drive interface, serial port, parallel port address conflict enough you busy for a while, not to mention multi-function cards generally do not support ATAPI protocol, which means even if you add the two multifunction cards, but also drive Is not installed on. Do not know that you do not remember the old ISA sound card, then take into account the 586 machine factory is no extra IDE interface, easy to mount CD-ROM, CD-ROM interface, the sound card on the left. Then you run errands, to the secondary market to find an old sound card on the line. Process in the sound card driver Sequence in general have the option to set optical drive, according to the prompts to install on the line. Software, because: 1), IDE driver installation error or a conflict with a driver if we did not install WIN98 or 95 IDE driver will be installed correctly, or when you open the device after installation Explorer View "hard disk controller," which found a yellow exclamation mark, the time of the drive may be found. Under normal circumstances, when we enter the safe mode, of the drive is not there. If we want to use the drive in safe mode, we can Autoexec.BA
- operationsystemnotfound
- How to change XPGHOST CD inside the content?
- Blue screen problems
- WINDOWS permanently activated, you on behalf of genuine
- windows7 the img file to install
- What depth of XP, DOS installation method
- windows startup items in liunx
- EXCEL HYPERLINK function of depth in
- The problem with UltraISO installed windows7
- How to adjust the virtual memory
- This information provided by the users.Thanks!
Computer Knowledge Copyright 2005-2015 All Rights Reserved.