Why have to press F1 each boot
[Users questions | Browse:123 | Favorites]
Users questions: Why should the beginning of each boot by pressing F1 to enter the CMOS setup del, then select "StandardBiosFeatures" under the "Halton", then "PageDown" flip key set NoError, and the DriveA and DriveB are set to NONE. Finally, press F10 to save and exit, so there will be no next time you start the F1 prompt solution of this online this seems to me that I did not ... StandardBiosFeatures, or in front of not Standar d or not followed by Bios, I have to open into two, and did not say Halton above all to help me ... you PC version is 2002 ... my computer shows like this ... you help me friends ...
Experts answer: may be your BIOS battery is no electricity, and if Is replace, if it is for other reasons by the following methods of repair. Press F1 to enter the system starts the reason and solution: boot according to F1 this is an error caused by the BIOS settings are generally caused by the following situations. 1, no floppy drive but the floppy drive enabled, you can disable the floppy drive. Power by DE L into the BIOS, choose: STANDARDCMOSFEATURESDRIVEA: set NoneDRIVEB: set to None, press F10 to save, enter "Y" press Enter. 2, memory problems or CPU frequency is changed, replace the memory, recovery BIOS default values. 3, had hung up two hard drives in the BIOS set to double hard drive, then remove one of the time but forgot to change the BIOS settings back, there will be the problem. As long as you can to restore BIOS defaults. 4, if the above setting is invalid, possibly CO MS battery is no electricity, and open the host, pull the coin under the COMS battery, replace battery. 5, to restore the BIOS default values: Boot or reboot the computer holding down the DEL key to enter the BIOS; find LoadFail-SafeDefaults, press the arrow keys to select After the carriage return in, prompted to confirm, press Y, Enter. Finally, choose Save & exitstep (Save Settings), you can simply press F10, press Y to enter auto-restart, the settings take effect. Some reasons can cause the occurrence of failure, the solution is as follows: First, the hard drive is IDE cable Cable connected, the cable must be connected at both ends (end with hard drives, plus other end of the motherboard), started no problem, if the CMOS, the floppy drive disabled, the problem still occurs, then only the floppy drive key open, the computer on all normal. Second, the addition, for data lines to try. Third, access to BI OS to see if the main hard top, if not, check the hard disk jumper to connect the motherboard and hard drive data line position. Ensure that the hard drive on the primary ide. Fourth, if you share an IDE cable with the drive, check the jumpers on the hard drive set to master, CD-ROM drive is set to slave. SETUP Chinese: monitoring error is found, look into POWERMANAGEMENTSETUP details, press the F1 key to continue the boot process, press the DEL key to enter COMS setting. Explanation: Some motherboards have hardware monitoring function, you can set the motherboard and CPU temperature Degree of monitoring, voltage regulator voltage output level of each fan speed monitoring and surveillance, the monitoring function when found to have abnormal boot, then the passage will appear, then you can set the options to enter COMS POWERMANAGEMENTSETUP, in the right ** FanMonitor **,** ThermalMonitor ** and ** VoltageMonitor ** see which part of the issue of an exception, then add to address. 2, prislavedrive-ATAPILNCOMPa tiblepressF1toResume may be your drive not connected or faulty, will be the best in the CMOS IDE port is set automatically. 3, PressF1tocontinue, DELtoenterSETUP boot and press DEL to enter BI
Experts answer: may be your BIOS battery is no electricity, and if Is replace, if it is for other reasons by the following methods of repair. Press F1 to enter the system starts the reason and solution: boot according to F1 this is an error caused by the BIOS settings are generally caused by the following situations. 1, no floppy drive but the floppy drive enabled, you can disable the floppy drive. Power by DE L into the BIOS, choose: STANDARDCMOSFEATURESDRIVEA: set NoneDRIVEB: set to None, press F10 to save, enter "Y" press Enter. 2, memory problems or CPU frequency is changed, replace the memory, recovery BIOS default values. 3, had hung up two hard drives in the BIOS set to double hard drive, then remove one of the time but forgot to change the BIOS settings back, there will be the problem. As long as you can to restore BIOS defaults. 4, if the above setting is invalid, possibly CO MS battery is no electricity, and open the host, pull the coin under the COMS battery, replace battery. 5, to restore the BIOS default values: Boot or reboot the computer holding down the DEL key to enter the BIOS; find LoadFail-SafeDefaults, press the arrow keys to select After the carriage return in, prompted to confirm, press Y, Enter. Finally, choose Save & exitstep (Save Settings), you can simply press F10, press Y to enter auto-restart, the settings take effect. Some reasons can cause the occurrence of failure, the solution is as follows: First, the hard drive is IDE cable Cable connected, the cable must be connected at both ends (end with hard drives, plus other end of the motherboard), started no problem, if the CMOS, the floppy drive disabled, the problem still occurs, then only the floppy drive key open, the computer on all normal. Second, the addition, for data lines to try. Third, access to BI OS to see if the main hard top, if not, check the hard disk jumper to connect the motherboard and hard drive data line position. Ensure that the hard drive on the primary ide. Fourth, if you share an IDE cable with the drive, check the jumpers on the hard drive set to master, CD-ROM drive is set to slave. SETUP Chinese: monitoring error is found, look into POWERMANAGEMENTSETUP details, press the F1 key to continue the boot process, press the DEL key to enter COMS setting. Explanation: Some motherboards have hardware monitoring function, you can set the motherboard and CPU temperature Degree of monitoring, voltage regulator voltage output level of each fan speed monitoring and surveillance, the monitoring function when found to have abnormal boot, then the passage will appear, then you can set the options to enter COMS POWERMANAGEMENTSETUP, in the right ** FanMonitor **,** ThermalMonitor ** and ** VoltageMonitor ** see which part of the issue of an exception, then add to address. 2, prislavedrive-ATAPILNCOMPa tiblepressF1toResume may be your drive not connected or faulty, will be the best in the CMOS IDE port is set automatically. 3, PressF1tocontinue, DELtoenterSETUP boot and press DEL to enter BI
- Recommended browser 360, it temporarily shut down ie6
- Expert to help me see my computer the CPU is large, pattern
- SharedStep?
- UT27626461 room to help find the next thank you
- 360 anti-virus software, virus scanning is safe and credibility of the results is the number
- Why Thunder look at the online viewing is always "temporarily not connect server"
- Always sound. . . . . ?
- configure a boot on vista update 0%, then a restart.
- Galvanized the national standard thickness tolerance
- Download the software under a Trojan virus you have to redo the system
- This information provided by the users.Thanks!
Computer Knowledge Copyright 2005-2015 All Rights Reserved.